Sor Pivot Seal Weatherproof Pressure Switch Manual de usuario descargar pdf (Pagina 1)

Form 496 (01.13) ©SOR Inc.

1/8

Pressure Switches

for Process Applications

General Instructions

Registered Quality System to ISO 9001

Table of Contents

Electrical Connection ...........................1

Installation ....................................... 2

SIL Installation ..................................3

Process Connection ............................3

Calibration .......................................3

ATEX Marking Information .....................4

Declaration of Conformity .....................5

Electrical Connection

Storing excess wire or making wire lead splices inside the pressure switch housing will

interfere with pressure switch operation.

Design and

specifications are subject

to change without notice.

For latest revision, go to

www.sorinc.com

These instructions provide information for electrical

connection, installation, process connection, and

calibration. If the switch is a pivot seal sensor type

(piston 2 or 3), it is recommended for high-pressure

fluid power applications where high-shock pressure

and high-cycle rates are expected. Pivot seal sensors

are designed specifically for those applications.

NOTE: If you suspect that a product is defective, contact the

factory or the SOR

Representative in your area for a return

authorization number (RMA). This product should only be

installed by trained and competent personnel.

Electrical Power must be disconnected from explosion-proof models before

the cover is removed. Failure to do so could result in severe personal injury

or substantial plant damage.

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Pressure Switches

Form 496 (01.13) ©SOR Inc. 1/8Pressure Switches for Process ApplicationsGeneral InstructionsRegistered Quality System to ISO 9001Table of ContentsElec

Pagina 2 - Installation

2/8Form 496 (01.13) ©SOR Inc. Wire Lead Color CodeSPDTDPDT (2-SPDT)Vacuum SwitchInstallationBlue (C)Black (NO)Red (NC)Green (GND)PressureBlue (C)Black

Pagina 3 - Calibration

Form 496 (01.13) ©SOR Inc. 3/8Process ConnectionSecurely connect process line to pressure port using two wrenches: one to hold flats on pressure port,

Pagina 4 - ATEX Marking Information

4/8Form 496 (01.13) ©SOR Inc. ATEX Marking InformationSample NameplateDrawing 072004xManufacturer’sRegistered TrademarkATEX Listing InformationProduct

Pagina 5 - of Conformity

Form 496 (01.13) ©SOR Inc. 5/8Declaration of ConformityFor ATEX Certi ed Models R Series Pressure SwitchesSOR Inc.14685 West 105th StreetLenexa, Ka

Pagina 7

Pagina 8 - Printed in USA www.sorinc.com

8/8Form 496 (01.13) ©SOR Inc. 14685 West 105th Street, Lenexa, KS 66215  913-888-2630  800-676-6794 USA  Fax 913-888-0767Registered Quality S

Mas documentos para Sensores Sor Pivot Seal Weatherproof Pressure Switch

a Ver el documento Sor Pivot Seal Weatherproof Pressure Switch Manual de usuario

Sor Pivot Seal Weatherproof Pressure Switch Manual de usuario (4 paginas)

Comentarios a estos manuales

Sin comentarios

Sor Pivot Seal Weatherproof Pressure Switch Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Sor Pivot Seal Weatherproof Pressure Switch. SOR Pivot Seal Weatherproof Pressure Switch User Manual Manual de usuario

Indice de contenidos

Mas documentos para Sensores Sor Pivot Seal Weatherproof Pressure Switch

Comentarios a estos manuales

Sor Pivot Seal Weatherproof Pressure Switch Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Sor Pivot Seal Weatherproof Pressure Switch. SOR Pivot Seal Weatherproof Pressure Switch User Manual Manual de usuario

Indice de contenidos

Mas documentos para Sensores Sor Pivot Seal Weatherproof Pressure Switch

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Sor Pivot Seal Weatherproof Pressure Switch